DateCityStateEmployerBody PartEvent
2021-11-15West Palm BeachFlAcademy Bus, LLCHand(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was working in the engine compartment of a bus. The bus was turned on and the employee's hands were caught in a pulley. The employee's left hand was injured.
2021-10-24Oklahoma CityOkRush Truck Centers of Oklahoma, Inc.Leg(s)Struck by falling part of powered vehicle still attached
A Rush employee was working under a garbage truck cab that had been jacked halfway up. The cab fell and pinned his arms and leg against the engine. He was pinned for some time before being found, and was hospitalized to lower toxin levels in his leg.
2021-09-14PennsaukenNjCaliber CollisionFinger(s), fingernail(s)Struck by falling object or equipment
As an employee was removing an engine from a truck, the engine fell on the employee's left middle finger. The employee's finger was partially amputated.
2021-09-13Grove CityPaGE Transportation, a Wabtec CompanyHand(s)Injured by slipping or swinging object held by injured worker
An employee was using a de-tensioner to loosen a bolt that was installed in a locomotive engine casing. The reaction arm slipped off the main bolt and caught the employee's hand against the engine block. The employee sustained fractured bones in the hand that required hospitalization and surgery.
2021-09-07Pearl HarborHiDepartment of the NavyFingertip(s)Caught in running equipment or machinery during maintenance, cleaning
The injured employee was working in a two-person team conducting troubleshooting and repair of an onboard boat engine. The engine started and the injured employee's right index fingertip was amputated. The cowling guards had been removed to provide access to the engine components.
2021-08-27BraggsOkErvin Cable Construction, LLCFingertip(s)Machinery or equipment incident on water vehicle
Two employees were troubleshooting a pontoon boat motor. The motor began to run and the flywheel of its engine contacted an employee's right middle finger. The employee's fingertip was amputated.
2021-08-18TampaFlStarlink Construction Utilities, LLCNonclassifiableVehicle or machinery fire
An employee was mixing bentonite with a mixing machine. A small engine caught fire, and the employee suffered second- and third-degree burns. He was hospitalized.
2021-08-16Yonges IslandScStevens Towing Co.,Inc.Finger(s), fingernail(s)Struck by falling object or equipment
Two employees were lifting a 59-pound piece of steel plate into the engine room of a vessel. One of the employees, standing on the ground, lifted the plate up to the other and released it. As the other employee was lifting it into the vessel, it fell down through a hole. The first employee's left ring and middle fingers were caught between the plate's edge and a steel I-beam. Both fingers suffered multiple compound fractures; the little finger and half the ring finger were medically amputated th
2021-08-04BedfordPaJLG Industries, IncFinger(s), fingernail(s)Contact with objects and equipment
An employee was preparing a new lift to receive an engine. His right pinky finger was pinched and he sustained a loss of soft tissue.
2021-07-29JohnstownPaLaurel Motors Inc.PelvisStruck by powered vehicle-nontransport, n.e.c.
An employee was on their knees with their upper body in a car while attempting to connect scanning equipment to an engine control module. The car went into drive and lurched forward. The driver's door struck a post and pinned the employee between the door and doorframe, resulting in a broken pelvis.
2021-07-23HazlehurstGaBeasley Timber Co. Inc.Leg(s)Fall or jump from vehicle in normal operation, nonroadway
An employee was driving a front-end loader from one yard to another when the engine shut off, leaving him with no power to control it. He jumped clear of the loader and broke his left leg when he hit the ground.
2021-07-14LindenPaWilliam L Robinson Concrete Contractors, Inc.Chest, except internal location of diseases or disordersOther fall to lower level less than 6 feet
An employee was standing on a 10-inch step stool performing maintenance on a pickup truck engine when they fell off the step stool and landed on a wheeled tool chair. The employee suffered six fractured ribs and a collapsed lung.
2021-07-07LavonTxChris Harp Construction, LLCWrist(s)Contact with hot objects or substances
An employee was performing maintenance and mechanical work at the concrete plant. A generator stopped working because it was overheated. The employee cooled the generator engine using a hose. The employee then lifted the radiator cap lever to release steam. After the steam was released, he opened the cap and pressurized hot water was released causing third degree burns to their wrist and second degree burns to their arm and chest.
2021-06-30SeguinTxCaterpillar Inc.Fingertip(s)Contact with objects and equipment
An employee was using an overhead grid crane when their right middle finger was pinched between the engine head assembly and the transport rack resulting in amputation of the fingertip just below the nail bed.
2021-06-06NaknekAkPeter Pan Seafoods IncThigh(s)Fall on water vehicle
While inspecting a boat, an employee fell through an open hatch leading to the engine room. The employee suffered a broken femur, caused by the ladder and the floor the employee landed on.
2021-05-28HoustonTxTBC RETAIL GROUP, INC.Fingertip(s)Caught in running equipment or machinery during maintenance, cleaning
An employee finished an oil change and was cleaning the car's engine when his pinky fingertip was amputated by the fan belt.
2021-04-20IowaLaProgressive Tractor & Implements, LLCFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was troubleshooting a tractor engine. The employee's hand slipped into the turbo intake, and the tip of his left little finger was amputated at the first joint.
2021-04-01BrownsvilleTxAll Star Metals, L.L.C.Foot (feet)Compressed or pinched by shifting objects or equipment
An employee was removing a bolt from an engine block when the block sank due to rain and crushed the employee's foot, resulting in broken bones.
2021-03-30LawtonOkUnited States Department of Defense US ArmyFingertip(s)Struck against moving part of machinery or equipment
An employee was diagnosing an issue with a military vehicle when their left thumb struck against the vehicle's engine fan, amputating the thumb tip.
2021-03-15MobileAlMCG Workforce Solutions, LLCFinger(s), fingernail(s)Injured by slipping or swinging object held by other person
A temporary employee was controlling a come-a-long on one side of a flat plate while another worker was using a 20-pound steel hammer to strike the plate and move it into position inside the engine room of a vessel which was on shore/dry dock. The temporary employee was manually shaking the plate to see if it would slide down under its own weight when his left hand was struck by the hammer. The injured employee was wearing protective leather gloves at the time. His middle finger was broken and l
2021-01-29BaytownTxTalke USA Inc.Finger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was performing maintenance on a running truck engine belt and amputated their right pinky finger.
2021-01-15BrooklynNyHi-Lume CorpFinger(s), fingernail(s)Entangled in other object or equipment
An employee was starting a generator by pulling a drawstring with a piece of wood attached to it when the drawstring was sucked back into the engine. The piece of wood struck the employee's left ring finger, resulting in amputation.
2020-10-07OrlandoFlMears Destination ServicesFingertip(s)Caught in running equipment or machinery during regular operation
An employee was emptying the septic tank on the back of the bus. When the employee went to close the service door, his right hand was caught in the engine's fan belt resulting in amputation of the right ring fingertip.
2020-09-23HarlemGaDBI Services LLCLeg(s)Ignition of vapors, gases, or liquids
An employee was filling the pressure washer with gas. The tank slipped from his hand and fuel splashed onto his legs. The gas was ignited by the hot engine and one of the employee's legs was burned.
2020-09-09New HavenCtNPL Construction CompanyFingertip(s)Caught in running equipment or machinery during regular operation
On September 9, 2020, an employee was attempting to start a vibrating tamper in order to continue compacting backfill material in a completed excavation. The employee pulled the starter cord multiple times. After the pull which started the engine, the pull cord of the vibrating tamper did not recoil correctly. The employee gathered the excess cord in his left hand in order to prevent an additional slip, trip, or fall hazard. When he engaged the throttle of the machine with his right hand, the pu
2020-08-24Crystal LakeIlDiesel Redemption Inc.PelvisPedestrian struck by vehicle backing up in nonroadway area
On August 24, 2020, an employee was servicing a diesel engine when he was struck by a forklift being operated in reverse, suffering a fractured pelvis.
2020-08-18Sturgeon BayWiH & H Utility Excavating, Inc.NonclassifiableIgnition of vapors, gases, or liquids
An employee was removing the gas cap from a gasoline engine that was in a semi-trailer. The vapor from the fuel ignited, severely burning the employee.
2020-07-28CelebrationFloridaF&H Electrical Contractors, Inc. Upper and lower limb(s)Fire
An employee was filling up a small engine with gas. A fire started and burned the employee's legs and hand.
2020-06-26Port BolivarTexasCallan Marine LTD.Fingertip(s)Machinery or equipment incident on water vehicle
An employee was removing an air breather off of a boat motor when the engine's turbo pulled the employee's finger into the engine rotor blade, resulting in a right index fingertip amputation.
2020-06-04OrlandoFloridaLouisiana Machinery Company, LLCFinger(s), fingernail(s)Struck by swinging or slipping object, other than handheld, n.e.c.
An employee was installing a 550-pound blower on a generator engine. While the employee was raising the blower into position with a half-ton chain, the blower was caught between the generator and its A-frame. While being pulled loose, it swung and caught the employee's right little finger against the generator's A-frame. The employee suffered an amputation to the finger.
2020-05-22DumasTexasNutrien Ag SolutionsForearm(s)Struck by falling object or equipment, n.e.c.
An employee was performing maintenance on a wheel loader (front-end loader) and removed an access plate to the bottom of the engine compartment. After the fasteners were removed, the access plate fell to the floor and crushed the employee's forearm between the plate and the floor. The employee suffered damage to the muscle and connective tissue (no broken bones).
2020-05-05GainesvilleGeorgiaRush Truck CenterMultiple body partsOther fall to lower level
A service technician was standing on the frame rail of a truck and torqueing engine cylinder head-bolts using a torque wrench. He fell to the floor, suffering a broken hip and wrist.
2020-04-27ClermontFloridaZenodro Homes, Inc.Fingertip(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was storing a golf cart that was not working. He attempted to accelerate the cart to get it going again. The cart was in reverse instead of neutral at the time and went backward. The cart's belt then pulled his finger toward the engine pulley, cutting and amputating his index fingertip.
2020-04-27East LiverpoolOhioSuperior Marine Services LLCFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was working on a marine engine with a rag in his hand. A belt pulled the rag, which then pulled his right index finger through the pulley. This caused the amputation of approximately half of the finger.
2020-04-21HendersonColoradoCummins Rocky Mountain LLCFinger(s), fingernail(s)Compressed or pinched by shifting objects or equipment
An employee was attempting to remove a superstructure from an engine using a crane when the down button on the crane was pressed instead of the up button. The superstructure then amputated the employee's right index finger.
2020-04-20CarlislePennsylvaniaThe Giant Co.Finger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
A mechanic was notified of a cooling issue on a refrigerator trailer in the fleet. He had just brought the trailer in from the yard and parked in the work bay of the trailer shop to begin the troubleshooting process. While performing the tension checks, the thermostat on the trailer triggered the engine to start. A belt pulled the mechanic's hand into a pulley and his fingers were caught at a pinch point. He sustained an amputation to the left middle finger at the first joint, and an amputation
2020-04-17YoungstownOhioAMG Resources CorporationLeg(s)Fall or jump from and struck by rail vehicle-transportation incident
An employee was in the process of switching railcars in the scrap yard when he slipped and fell from the engine landing beneath the railcar wheel as the railcar was moving. His right leg and left foot were crushed, resulting in a right leg amputation.
2020-04-07BeloitWisconsinFairbanks Morse EngineElbow(s)Other fall to lower level
An employee was sitting on a large engine, masking an electrical system off for painting. The employee moved to step onto a lift and fell to the ground, suffering a broken elbow.
2020-03-13AnnaTexasAuto ZoneFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was checking a customer's car when the engine belt amputated the employee's middle finger.
2020-01-24VallejoCaliforniaAlliance Marine Multiple body partsFall on water vehicle
Employees had been laying down fire cloth in the engine room to prepare for pipe fitting and welding repairs. An employee fell approximately 18-20 feet into the hull of a floating maritime academy training vessel and was found lying unconscious. The employee was hospitalized with injuries including gashes to the head and thigh requiring stitches and severe hematomas.
2020-01-24DentonTexasLone Star Coaches, Inc.Finger(s), fingernail(s)Caught in running equipment or machinery, n.e.c.
An employee was performing a pre-trip inspection on a vehicle when the employee's gloved right hand was caught and pulled into the engine's rotating belt. As a result, the employee's right thumb was amputated.
2020-01-13Oklahoma CityOklahomaWaukesha Pearce Industries LLCFoot (feet)Struck by discharged object or substance
An employee was power-washing engine parts with a high-pressure water hose. The water from the pressure wand cut through the employee's steel-toed right shoe, lacerating the foot.
2020-01-09HillsboroughNew HampshirFirst StudentFingertip(s)Caught in running equipment or machinery
An employee reached into the running engine of a bus and severed the tip of his finger.
2020-01-07FarmingtonArkansasAll Right Construction, Inc.Finger(s), fingernail(s)Caught in running equipment or machinery, n.e.c.
Two employees were performing a pre-trip inspection on a dump truck. While one employee was checking the fan belt, the second employee started the engine. The first employee's hand made contact with the moving pulley and fan belt, amputating the left index and middle fingers.
2020-01-06MeadeKansasDeLissa Ford Inc.Upper and lower limb(s)Struck by object falling from vehicle or machinery-other than vehicle part
An employee was lifting an engine attached to a pallet out of a flatbed truck using a hydraulic hoist when the chains connected to the pallet and engine slipped, allowing the engine and pallet to roll toward the employee. The pallet with the engine struck him, tearing open his left arm and pushing his left knee sideways, causing tendon damage. He was hospitalized and had surgery.
2019-09-19AustinTexasAustin HLK,Inc.Fingertip(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was replacing a separator cap on a back engine on a sweeping truck when the blades on the radiator fan amputated two of the employee's fingertips.
2019-09-18PensacolaFloridaSignet Maritime, Inc.BODY SYSTEMSExposure to environmental heat
On September 19, 2019, an employee was about to remove a 1.5 gate bilge valve inside a ship vessel's engine room (offshore towing vessel) when he collapsed and then regained consciousness. The employee was hospitalized for dehydration and heat stress.
2019-09-18ColumbusMississippiPaccar Engine CompanyFinger(s), fingernail(s)Caught in or compressed by equipment or objects
An employee was pushing an engine block onto a conveyor when their right thumb was pinched between the engine block and a clamp inside a machine. The employee sustained a laceration and an open fracture to the thumb.
2019-09-06CarrolltonTexasAER MANUFACTURING, L.P.Fingertip(s)Caught in or compressed by equipment or objects
An employee was pushing an engine block from one conveyor belt to another. The employee's left middle finger got caught in the rubber grate of the pallet the engine block was on; the tip was amputated.
2019-09-03MonroeWisconsinCentury Fence CompanyLower leg(s)Pedestrian struck by forward-moving vehicle on side of road
An employee was working with an engineer to complete layout for a project on a state roadway. While on the shoulder of the road the employee was struck by a motor vehicle and sustained a compound fracture of the tibia/fibula.
2019-09-01Patuxent RiverMarylandU.S. Department of the NavyFinger(s), fingernail(s)Struck by falling part of powered vehicle still attached
An employee was inspecting under the hood of a fire truck's engine compartment when the hood shut on the employee's right index finger, causing an amputation.
2019-08-31Watford CityNorth DakotaBlackduck Power Equipment, IncArm(s)Vehicle or machinery fire
An employee was cleaning a semi-truck engine when his right arm caught on fire, sustaining second or third degree burns.
2019-08-28MiamiFloridaLSG SKY CHEFS INC.Hand(s)Caught in running equipment or machinery
Changing the brushes of an engine. A cable got caught by the rotating engine. The employee attempted to retrieve it and his right hand was pulled to the engine. He suffered a severe laceration on the upper part of the hand.
2019-08-27MiddlefieldConnecticutTextron Specialized Vehicles Inc.Finger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was replacing a starter generator bracket on a gas-powered golf cart. This required removal of the starter. He removed the seat to gain access to engine compartment and knelt on the floorboard of the car to get into position to perform the task. He loosened the starter generator adjustment bolt so that the starter generator belt could be removed. After loosening the adjustment bolt, he began to pull the belt off the front pully on the starter generator. At the same time, his knee pre
2019-08-22ProvidenceRhode IslandRhode Island HospitalBODY SYSTEMSExposure to environmental heat
While working in a power plant, an engineer became dehydrated due to the heat. He was hospitalized.
2019-08-22CamdenNew JerseyMy Auto StoreFoot (feet)Struck by falling object or equipment, n.e.c.
An employee was preparing to hook up a hoist to an engine when it fell off the table it was on and pinned his feet, fracturing them.
2019-08-19LincolnNebraskaNMC GroupMultiple trunk locationsBending, crawling, reaching, twisting-single episode
An employee was rebuilding a diesel engine at a customer's power generation plant when he attempted to move a four-wheel trailer out of the building that was in his way. The trailer was on a slight incline and, due to the size and weight, got away from him and headed toward some valves and piping along the fence line. He attempted to get in front of it to redirect and steer it when he twisted his lower back and pelvis area, causing factures to the lower vertebra and pelvis. He was hospitalized.
2019-08-17WailukuHawaiiSea Sport Cruises, Inc.Upper and lower limb(s)Explosion or fire on water vehicle
An employee was using heat from a blow torch to help loosen a bolt from a vessel's engine when an explosion occurred. The employee suffered first and second degree burns to both arms and both knees.
2019-07-31Patuxent RiverMarylandU.S. Department of Navy/Patuxent RiverFingertip(s)Caught in running equipment or machinery, n.e.c.
A mechanical engineer technician was upgrading a load bearing machine from manual to automatic when his glove and right index finger got caught between the sprocket and chain. The right index fingertip was amputated.
2019-07-26BranfordConnecticutTA Operating, LLCFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
On July 26, 2019, a technician was installing a short belt to circumvent the air conditioning system in the engine compartment of a truck. The employee's right second and third fingers got caught between a pulley and drive belt resulting in partial amputations at the first joints.
2019-07-10Cherry PointNorth CaroliU. S. Dept. of NavyWrist(s)Other fall to lower level
An employee was troubleshooting an aircraft from the cockpit. The employee exited the left side of the cockpit and stepped on the engine intake. When his weight shifted to his right foot, his foot slipped off the intake and he fell off the aircraft. He sustained a compound fracture to the wrist that required hospitalization and surgery.
2019-07-08ZapataTexasElite Compression Services, LLCFingertip(s)Compressed or pinched by shifting objects or equipment
An employee was performing maintenance on a natural gas compressor. He was turning over an engine by barring over when his left pinky finger was caught between the bar and the guard for the bull wheel. Two centimeters of the tip were amputated.
2019-06-25HazlehurstGeorgiaThompson Hardwoods, Inc.Multiple body partsContact with hot objects or substances
An employee was operating a loader with a grapple attachment to unload tree logs from a truck when he noticed the temperature indicator light flashing. The employee turned off the loader and waited a few minutes to let the engine cool off. Next, the employee started to remove one of the radiator caps on the loader. As he started removing the cap, hot water and steam released from that area, striking the employee. He sustained third degree burns to his left wrist, left arm, and left side torso.
2019-06-21SarasotaFloridaResource Recovery Systems, LLCHand(s)Caught in or compressed by equipment or objects
An employee was trying to release the brake on the engine twister of a compactor bailer using a crescent wrench. The twister motor spun out and the wrench struck the employee's right hand causing an injury that required surgery.
2019-06-07Belle ChasseLouisianaHutco, Inc.Multiple body partsStruck by swinging or slipping object, other than handheld, n.e.c.
An employee was removing a gear from an engine using a crane. The employee was unhooking a come-a-long when the crane operator noticed tension on the gear box. The crane operator lowered the gear and the employee unhooked the come along. The gear box came loose, swung, and hit the employee, pinning him between the gear box and bulk head. He fractured his left arm and ribs on the left side.
2019-06-06DenverColoradoSouthwest AirlinesFingertip(s)Compressed or pinched by shifting objects or equipment
An employee was installing an engine cradle bolt when the cradle shifted and partially amputated the tip of his left thumb.
2019-05-14TeaSouth DakotaJR Koop, Inc. Arm(s)Ignition of vapors, gases, or liquids
An employee was trying to find a gas leak on a heater that was returned by a customer. In order to test the fuel injector spray pattern, the employee pressed the start button. Fuel was expelled from the engine and caught fire. The employee's right arm was burned.
2019-05-14CraigsvilleWest VirginiColumbia West Virginia CorpFinger(s), fingernail(s)Compressed or pinched by shifting objects or equipment
An employee was checking oil on a loader. He went to shut the side engine panel/cowling when his right index finger was smashed in the hinge area of the panel, requiring surgical amputation of the bone.
2019-05-06SeabrookTexasSpecialty Tank ServiceMultiple body partsOther fall to lower level more than 30 feet
An employee was dismantling an engineered scaffold and fell approximately 57 feet. The employee was hospitalized for compound fractures to his legs and ankles and two fractured ribs.
2019-05-05SewarenNew JerseyPSEG Power LLCFinger(s), fingernail(s)Caught in running equipment or machinery during regular operation
An employee was polishing a tool on the engine lathe and his finger got caught.
2019-04-26IrvingTexasUnited Rentals, Inc.Finger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
Two employees were troubleshooting the sensor on a skid steer unit. The unit started and an engine component partially amputated an employee's right index finger.
2019-04-10WoburnMassachusettAlbrecht Autoland Group Finger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was under a vehicle, troubleshooting a component. The engine started, and the compressor/alternator belt caused the amputation of one of the employee's fingers and the partial amputation of another.
2019-04-10Dodge CityKansasJacobs Engineering Group, Inc.Leg(s)Caught in or compressed by equipment or objects
A temporary Jacobs Engineering employee's leg was caught in the deck of a mower. His leg was broken.
2019-03-26CarrolltonTexasAER ManufacturingHand(s)Injured by slipping or swinging object held by injured worker
An employee was breaking a bolt on an engine head with a breaker bar when the bolt gave way, which caused the employee to smash his hand into the engine head. He suffered a laceration to his left middle finger and crushed part of the bone.
2019-03-19Kirtland AfbNew MexicoM1 Support ServicesForearm(s)Fall, slip, trip
An employee was working on a helicopter engine when he slipped and fell on the engine firewall, lacerating his left forearm. He was hospitalized, requiring surgery.
2019-03-01South HollandIllinoisLove's Travel Stops & Country StoresFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was working on a customer's semi trailer. The engine was started, causing the trailer to lower onto the employee's right hand. The employee's index and middle fingers were crushed.
2019-02-11BolingbrookIllinoisPeterbilt of Illinois - Joliet, Inc.Hip(s) and leg(s) Struck or run over by rolling powered vehicle
On February 11, 2019, at 1:30 p.m., a journeyman mechanic was performing a diagnostic test on a tractor (truck). While standing inside the engine bay of the truck between the frame and the left steer tire axel, the vehicle started and the truck moved forward pinning the employee under the steer tire. The employee's upper leg was crushed and the hip and ankle were fractured.
2019-02-06DaytonOhioMoody's of Dayton, Inc.Fingertip(s)Caught in running equipment or machinery during maintenance, cleaning
An employee was loosening nuts and bolts on the engine of a drill rig when his finger was caught between a drive belt and pulley, resulting in a fingertip amputation.
2019-01-29New BostonTexasVSE CorporationFinger(s), fingernail(s)Caught in or compressed by equipment or objects
While working on a training project (maintenance and rebuilding of a diesel engine) an employee caught two fingers on their left hand between the camshaft and the front of the engine. The left middle and ring fingers were lacerated near the nail and partially amputated.
2019-01-15Golden MeadowLouisianaLouisiana Machinery Company, LLC.Fingertip(s)Struck against moving part of machinery or equipment
An employee was looking for a crescent wrench and dropped his flashlight. He reached for the falling flashlight and his hand contacted the fan blade of a running generator engine. The employee sustained an amputation to the right index fingertip and a laceration between the thumb and index finger on the right hand.
2019-01-14HoustonTexasRiver Oaks Chrysler JeepFinger(s), fingernail(s)Caught in running equipment or machinery during maintenance, cleaning
An employee suffered partial amputation of the right index finger during engine maintenance.
2019-01-04KerseyColoradoBill Barrett CorporationHead and neckFire
An engine backfired and ignited gas in the building, causing an explosion and fire that burned an employee's face and neck.
2019-01-02San AntonioTexasFHE USA LLCFinger(s), fingernail(s)Explosion of pressure vessel, piping, or tire
An employee was troubleshooting the hydraulic system on a customer's skid to get the hydraulic pump to run. He started up the engine and an unexpected release of hydraulic energy occurred. He attempted to open the dump valve and the discharge hose exploded with his hand on it, releasing oil and severely lacerating his right index finger.
2018-09-25GalesburgIllinoisDealers Choice Auto Auction IncFinger(s), fingernail(s)Struck by falling part of powered vehicle still attached
On September 25, 2018 an employee was checking fluids in the engine compartment of a vehicle when a gust of wind blew the vehicle hood off of the hood strut. The hood then closed on the employee's left hand, resulting in a left middle finger amputation.
2018-08-23SummitIllinoisM&K Employee SolutionsMultiple body partsContact with hot objects or substances
An employee was servicing a truck from underneath when hot antifreeze/engine coolant poured onto him. He suffered burns to the face, arms, and chest.
2018-08-20RigbyIdahoNoreen ConstructionMultiple body partsVehicle or machinery fire
An employee was trying to start a truck engine by adding fuel to the carburetor. There was a fire, and the employee suffered burns to the torso and left arm.
2018-08-09CincinnatiOhioBuilding Systems Erectors, Inc.Multiple body partsFall through surface or existing opening 21 to 25 feet
Employees were performing steel erection activities and placing clips, insulation and roof sheeting onto a pre-engineered metal building. The employees were walking and working from a partial bundle of roof sheeting (approximately 3 sheets). During the operation, an employee stepped on an inadequately supported area of the roof sheeting partial bundle; the sheets bent down and the employee fell 21 feet to the ground below. The employee was hospitalized with a broken arm and tailbone.
2018-08-08San DiegoCaliforniaBAE SYSTEMS SAN DIEGO SHIP REPAIRForearm(s)Machinery or equipment incident on water vehicle
On August 8, 2018, employees were rigging an engine coupling on a ship when the tension in the chain fall released and the load shifted, pinning the injured employee's arm against the ship's piping. The weight of the load (coupling) was 4,800 lbs. The employee's right arm was crushed, fracturing the radius and ulna and requiring surgery.
2018-07-13WheelerTexasWAUKESHA-PEARCE INDUSTRIES, INC.Chest, except internal location of diseases or disordersOther fall to lower level
An employee was working from a catwalk to perform maintenance on the engine of equipment used to transport crude oils and liquids. While descending the ladder from the catwalk, the employee slipped and fell to the ground, resulting in rib fractures, abrasions to the arm and shoulder, and a collapsed left lung.
2018-07-12LolitaTexasInteplast Group, Ltd.Multiple body partsDirect exposure to electricity
An electrical engineer was checking a newly installed cooling fan in the drive cabinet and received electrical burns to both arms and the face.
2018-07-05OrlandoFloridaTitan Electric SoutheastMultiple body partsDirect exposure to electricity
An employee was on a scissor lift, installing a disconnect to an energized engine bus stop. The disconnect made contact with two phases, causing a short and an arc flash. The employee suffered burns to the skin on the neck, stomach, and left arm and hand.
2018-06-28MiamiFloridaPalm Beach Trucking, LLCFinger(s), fingernail(s)Contact with objects and equipment
An employee suffered an amputation to the right ring finger while working with a crane. The employee was injured by an engine turbo charger fan.
2018-06-27BataviaNew YorkContour Steel, Inc.Arm(s)Other fall to lower level
An employee was walking on the crane deck when he slipped and fell into the engine compartment, breaking his left arm and requiring hospitalization.
2018-06-26OdessaTexasTarga Midstream Services, LLCFingertip(s)Compressed or pinched by shifting objects or equipment
An employee was loading the engine pistons and cylinder liners onto a pallet to remove from the area for housekeeping purposes. He lifted the last piston by placing his fingers into the large holes on each side of the piston. The piston did not have rings installed on it. When he sat the piston (98 pounds) on the liner it slid into the liner catching two of his fingers between the piston and the liner, amputating the tips of two fingers on his left hand.
2018-06-26BedfordPennsylvaniaPenn Detroit Diesel Allison LLCHand(s)Struck by discharged object or substance
An employee was doing a compression test on an engine when diesel fuel was injected into his hand.
2018-06-11GrovetownGeorgiaJohn Deere Commercial Products, Inc.Finger(s), fingernail(s)Caught in or compressed by equipment or objects
An employee was pushing an assembled engine on an engine cart down a conveyor roller rack. As the employee attempted to slow down the momentum of the engine cart, his left index finger was pinched and amputated between the engine cart and a roller on the conveyor.
2018-05-11TylerTexasFire-Teck LLCBrainStruck by falling part of powered vehicle still attached
The employee was performing repairs on a fire truck while the truck's cab was being held up in a tilted position by a safety latch. The pivot point on the cab broke and released the cab lock. The cab fell from its tilted position and the employee was crushed between the engine and cab frame. The employee sustained severe head trauma.
2018-04-23HanoverMassachusettHanover Automotive Group, Inc.Finger(s), fingernail(s)Contact with objects and equipment
An employee was working on a car engine when his finger came in contact with a sharp object, resulting in a left middle finger amputation.
2018-04-16RangelyColoradoSummit Midstream Partners LLCFingertip(s)Compressed or pinched by shifting objects or equipment
Two employees were trying to loosen a bolt to disassemble a coupler between an engine and compressor. One employee was on the engine side while the other (the injured employee) was on the compressor side holding a shim. When the employee on the engine side turned the bolt for the coupling assembly, the engine crank rolled and amputated the injured employee's left middle fingertip.
2018-04-03GonzalesLouisianaCommercial Fleet Truck and Equipment ServicesMultiple upper extremities locationsOther fall to lower level 6 to 10 feet
An employee was standing on the engine compartment of a manlift lining up the holes on the boom to apply the pin. As another worker hit the pin, it vibrated and caused the employee to lose his balance. He fell 7' 3" to the ground, fracturing his right wrist, dislocating his left collarbone, and suffering two contusions to the back and front of his head. He was hospitalized.